PLUMBING BASICS: BEFORE INSTALLING A BATHTUB

Plumbing Basics: Before Installing a Bathtub

Plumbing Basics: Before Installing a Bathtub

Blog Article

Maintenance Sign-Up

Have you been searching for help concerning How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub Yourself
Installing a tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently easily accessible, the task can relocate easily; if you need to open a wall surface to remove the old tub and also position the brand-new bath tub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old bathtub as well as set in the new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. As opposed to hiring a service provider to take over a halfway-completed project, it is far better to consider using one prior to you start. Possibilities are you might need an expert plumber to make tube connections.
This write-up will aid you set up a brand-new tub in your restroom if you have actually already bought a brand-new tub and do not require to transform the setup of your previous supply of water pipes.
Your tools as well as product checklist should comprise the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installation


    To start with, the supporting structure supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
    Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final placement.

    Removing Old Taps


    If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, turn on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome due to the limited accessibility that is frequently the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing compound.
    Prior to moving on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

    Mounting the Tub


    Utilizing both wooden boards under its feet, position the bath tub in the required position. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
    The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level as well as readjusting the feet on the tub until the level checks out degree.
    To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; then do the same for the various other tap.
    Switch on the water supply as well as check all joints and also new pipework for leakages as well as tighten them if essential. Fill the bathtub and likewise check the overflow electrical outlet and also the normal electrical outlet for leakages.
    Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the tub needs to wait up until the bathtub has been made use of a minimum of when as this will settle it into its final position.

    Fitting New Taps


    If the tails of the brand-new faucets are plastic, after that you will require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the current supply pipes.
    If you require to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next off, place the faucet in the placing hole in the bath/basin making certain that the washing machines remain in place between the tap as well as the sink. Protect the tap in place with the producer offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind should be connected to the faucet finishes initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the location where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to split an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, resulting in problems with wetness as well as possible leakages to the ceiling below.
    You can choose from a variety of coloured sealants to blend in your components as well as fittings. They are offered in tubes and also cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can fracture rather early if you do not take into account this motion prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily available on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or water resistant sticky and grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub Yourself

    I hope you enjoyed reading our excerpt on Installing A Bathtub. Many thanks for taking a few minutes to read our content. Liked our blog entry? Please share it. Let another person discover it. We treasure reading our article about How to Install a Bathtub.


    Superior emergency plumbing? We're here.

    Report this page